The List Below Consists Of Items Which Can Be Purchased Separately as Spares
I/P CONVERTERS
The I/P bolt-on kit used here is directly interchangeable with one used on the positioner.
The standard range is 4-20mA = 20-100kPa. Please note: other ranges may affect price and delivery
STANDARD (NON - I/S) Including a 5-micron filter Retrofit mounting kit c/w u-bolts and feedback
ANCILLARIES
Intrinsically safe SABS - (SABS - Ex ib IIC T6)
Mounting hardware (2" pipe bracket powder-coated mild steel)
Mounting hardware (Plate only powder coated mild steel)
ACTUATOR POSITION FEEDBACK - with the positioner
This module is designed to fit onto our positioner. The old lid is replaced and the feedback module is mounted to a new lid.
Alternatively, the module can be supplied as a loose unit with a NAMUR bracket.
Digital feedback - switch boxes (for on/off indication)
Mechanical type
Proximity type (3 wire PNP DC with amplifier
Proximity type (2 wire 24V DC)
Proximity type ( Ex is IIC T6 2 wire Namur type)
(2 mechanical micro switches (V155 1 A5 220V, 15A)
(2 proximity switches (P+F: NBB2-V3-E2-24V DC)
(2 proximity switches (P+F: NBB3-V3-Z4-24V DC)
(2 proximity switches (P+F:NJ2-V3-N-8V DC)
FULL ANALOG FEEDBACK (for continuous indication)
4 - 20mA (standard)
4 - 20mA (I/S) SABS certified to Ex ib IIC T4
suitable for a two-wire 4 - 20mA feedback in a non-hazardous environment
RECOMMENDED SPARES
I/P module
KIT 7
KIT8
KIT 9
KIT 10
KIT 11 (s)
KIT 11
KIT 14
KIT 14 (s)
NP
PP or PM
EP or EM
CAM
CAMSHAFT
GAUGE
FILTER
DIAPHRAGM
POSITIONER LID
I/P FILTER PLUG
LINEAR LONG BEARING KIT
P0289
P0259
I/P module
Range lever kit
Primary lever kit
Seal kit
E-clip kit
I/P module
I/P module
Spool assembly
Spool assembly
Pneum blanking plate
Pneum bolt on kit
I/P bolt on kit
Std or split range cam
International shaft
AFB board
AFB potentiometer
(Control Air Type 590)
( A complete range lever kit)
(A complete primary lever kit)
(All o-rings, seals and diaphragm
(All E-clips in stainless steel)
(Control Air Type 590)
(Control Air Type 590)
(With spool retainer block, o-rings amd screws)
(Only spool block and spindle)
(Blanking off palte, o-rings and screws)
(Signal block, gauge, screws, 1/4" plugs and o-rings)
(kit 11 module, housing, screws and o-rings)
(0-1000kPa or 1 -160kPa)
(5 micron, 1/4" pipe, manual drain without a nipple)
(For the positioner)
(Window lid)
(Presses into the I/P base)
(5x 604 bearings, 8x retainer disk & 5x M4 nylocs)
(PC board for the analogue feedback module)
(Potentiometer for the analogue feedback module)
SERVICE AND REPAIRS
Positioner service
Casting enclosure
I/P enclosure
(Strip, clean, replace all seals & any damaged parts except I/P, spool assembly and gauges)
(Box, lid and other parts for P/P)
(I/P base and lid complete with filter plug)
